Why is Arduino resetting while driving motors?Question different ways of connecting L298N motor driver board to arduino and motors and powering themPowering motorsDriving stepper motors adafruit motor shield v2Mega pin stuck high after driving optocouplerMotors settingsControlling 5 DC motors with ArduinoRunning multiple motors simultaneouslyDriving two stepper motors using one stepper motor driverCan removing lines of code destroy a motor driver and make it catch fire?Will this power supply work with a MG-996R Servo?
Why has "pence" been used in this sentence, not "pences"?
Visiting the UK as unmarried couple
Divine apple island
How does the reference system of the Majjhima Nikaya work?
why `nmap 192.168.1.97` returns less services than `nmap 127.0.0.1`?
Does the Mind Blank spell prevent the target from being frightened?
Can I sign legal documents with a smiley face?
On a tidally locked planet, would time be quantized?
Create all possible words using a set or letters
Can a Necromancer reuse the corpses left behind from slain undead?
Translation of Scottish 16th century church stained glass
How can Trident be so inexpensive? Will it orbit Triton or just do a (slow) flyby?
Varistor? Purpose and principle
anything or something to eat
Query about absorption line spectra
Could the E-bike drivetrain wear down till needing replacement after 400 km?
Filling the middle of a torus in Tikz
Customize circled numbers
Is it possible to have a strip of cold climate in the middle of a planet?
A Permanent Norse Presence in America
What is the grammatical term for “‑ed” words like these?
Should spaces be used when writing foreign names in katakana?
Freedom of speech and where it applies
What major Native American tribes were around Santa Fe during the late 1850s?
Why is Arduino resetting while driving motors?
Question different ways of connecting L298N motor driver board to arduino and motors and powering themPowering motorsDriving stepper motors adafruit motor shield v2Mega pin stuck high after driving optocouplerMotors settingsControlling 5 DC motors with ArduinoRunning multiple motors simultaneouslyDriving two stepper motors using one stepper motor driverCan removing lines of code destroy a motor driver and make it catch fire?Will this power supply work with a MG-996R Servo?
I am driving motors for my line-follower project . The circuit schematic is given below 
The power source is a 11.1V 2200mAh 25C Lipo . Practically the cells give 11.5-12V. I used a switching buck regulator to step down the voltage. However , when i run my robot on track after few seconds,the arduino tends to reset and run again. This problem typically arises when i drive the motors at higher PWM(above 180 on analogWrite function). Since i use PID, limiting the PWM means i have to drive at lower speeds which i do not want.
I am providing links for the items i used for my circuit.
1) BUCK CONVERTER - https://www.amazon.in/LM2596S-Converter-Module-Supply-1-23V-30V/dp/B0784PYZ97/ref=sr_1_14_sspa?crid=2XRBYP632OY0B&keywords=buck+converter&qid=1553455574&s=electronics&sprefix=buck+c%2Celectronics%2C298&sr=1-14-spons&psc=1
2) MOTOR DRIVER - https://www.amazon.in/Generic-E_14013096-Tb6612Fng-Arduino-Microcontroller/dp/B01DAA6GMC/ref=sr_1_1?crid=TKGYYCKNQJCK&keywords=tb6612fng+dual+motor+driver&qid=1553455725&s=gateway&sprefix=tb66%2Celectronics%2C812&sr=8-1
3) IR SENSOR MODULE - https://www.amazon.in/Products-Channel-Analogue-Digital-Follower/dp/B07GXL5L7J/ref=sr_1_2?keywords=ir+sensor&qid=1553455761&s=electronics&sr=1-2
4) DC MOTORS - https://www.amazon.in/Invento-Kg-cm-Shaft-Torque-Geared/dp/B07CKMFYDG/ref=sr_1_34?crid=32XN84K8LZ4PJ&keywords=dc+motor+500+rpm&qid=1553455839&s=gateway&sprefix=dc+motor+500%2Caps%2C320&sr=8-34
The sensor array draws 150mA at peak. Any suggestions as to where the problem might lie would be of great help. Thank you .
arduino-mega power motor ir
asked 2 hours ago
user9999114user9999114
61
New contributor
user9999114 is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.
add a comment |
I am driving motors for my line-follower project . The circuit schematic is given below
The power source is a 11.1V 2200mAh 25C Lipo . Practically the cells give 11.5-12V. I used a switching buck regulator to step down the voltage. However , when i run my robot on track after few seconds,the arduino tends to reset and run again. This problem typically arises when i drive the motors at higher PWM(above 180 on analogWrite function). Since i use PID, limiting the PWM means i have to drive at lower speeds which i do not want.
I am providing links for the items i used for my circuit.
1) BUCK CONVERTER - https://www.amazon.in/LM2596S-Converter-Module-Supply-1-23V-30V/dp/B0784PYZ97/ref=sr_1_14_sspa?crid=2XRBYP632OY0B&keywords=buck+converter&qid=1553455574&s=electronics&sprefix=buck+c%2Celectronics%2C298&sr=1-14-spons&psc=1
2) MOTOR DRIVER - https://www.amazon.in/Generic-E_14013096-Tb6612Fng-Arduino-Microcontroller/dp/B01DAA6GMC/ref=sr_1_1?crid=TKGYYCKNQJCK&keywords=tb6612fng+dual+motor+driver&qid=1553455725&s=gateway&sprefix=tb66%2Celectronics%2C812&sr=8-1
3) IR SENSOR MODULE - https://www.amazon.in/Products-Channel-Analogue-Digital-Follower/dp/B07GXL5L7J/ref=sr_1_2?keywords=ir+sensor&qid=1553455761&s=electronics&sr=1-2
4) DC MOTORS - https://www.amazon.in/Invento-Kg-cm-Shaft-Torque-Geared/dp/B07CKMFYDG/ref=sr_1_34?crid=32XN84K8LZ4PJ&keywords=dc+motor+500+rpm&qid=1553455839&s=gateway&sprefix=dc+motor+500%2Caps%2C320&sr=8-34
The sensor array draws 150mA at peak. Any suggestions as to where the problem might lie would be of great help. Thank you .
arduino-mega power motor ir
asked 2 hours ago
user9999114user9999114
61
New contributor
user9999114 is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.
The buck converter is producing 5.5 V? That may be too low for the VIN input on Arduino, where the voltage regulator needs at least 7 V and is therefore causing brown-out.
– MichaelT
19 secs ago
add a comment |
I am driving motors for my line-follower project . The circuit schematic is given below
The power source is a 11.1V 2200mAh 25C Lipo . Practically the cells give 11.5-12V. I used a switching buck regulator to step down the voltage. However , when i run my robot on track after few seconds,the arduino tends to reset and run again. This problem typically arises when i drive the motors at higher PWM(above 180 on analogWrite function). Since i use PID, limiting the PWM means i have to drive at lower speeds which i do not want.
I am providing links for the items i used for my circuit.
1) BUCK CONVERTER - https://www.amazon.in/LM2596S-Converter-Module-Supply-1-23V-30V/dp/B0784PYZ97/ref=sr_1_14_sspa?crid=2XRBYP632OY0B&keywords=buck+converter&qid=1553455574&s=electronics&sprefix=buck+c%2Celectronics%2C298&sr=1-14-spons&psc=1
2) MOTOR DRIVER - https://www.amazon.in/Generic-E_14013096-Tb6612Fng-Arduino-Microcontroller/dp/B01DAA6GMC/ref=sr_1_1?crid=TKGYYCKNQJCK&keywords=tb6612fng+dual+motor+driver&qid=1553455725&s=gateway&sprefix=tb66%2Celectronics%2C812&sr=8-1
3) IR SENSOR MODULE - https://www.amazon.in/Products-Channel-Analogue-Digital-Follower/dp/B07GXL5L7J/ref=sr_1_2?keywords=ir+sensor&qid=1553455761&s=electronics&sr=1-2
4) DC MOTORS - https://www.amazon.in/Invento-Kg-cm-Shaft-Torque-Geared/dp/B07CKMFYDG/ref=sr_1_34?crid=32XN84K8LZ4PJ&keywords=dc+motor+500+rpm&qid=1553455839&s=gateway&sprefix=dc+motor+500%2Caps%2C320&sr=8-34
The sensor array draws 150mA at peak. Any suggestions as to where the problem might lie would be of great help. Thank you .
arduino-mega power motor ir
asked 2 hours ago
user9999114user9999114
61
New contributor
user9999114 is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.
I am driving motors for my line-follower project . The circuit schematic is given below
The power source is a 11.1V 2200mAh 25C Lipo . Practically the cells give 11.5-12V. I used a switching buck regulator to step down the voltage. However , when i run my robot on track after few seconds,the arduino tends to reset and run again. This problem typically arises when i drive the motors at higher PWM(above 180 on analogWrite function). Since i use PID, limiting the PWM means i have to drive at lower speeds which i do not want.
I am providing links for the items i used for my circuit.
1) BUCK CONVERTER - https://www.amazon.in/LM2596S-Converter-Module-Supply-1-23V-30V/dp/B0784PYZ97/ref=sr_1_14_sspa?crid=2XRBYP632OY0B&keywords=buck+converter&qid=1553455574&s=electronics&sprefix=buck+c%2Celectronics%2C298&sr=1-14-spons&psc=1
2) MOTOR DRIVER - https://www.amazon.in/Generic-E_14013096-Tb6612Fng-Arduino-Microcontroller/dp/B01DAA6GMC/ref=sr_1_1?crid=TKGYYCKNQJCK&keywords=tb6612fng+dual+motor+driver&qid=1553455725&s=gateway&sprefix=tb66%2Celectronics%2C812&sr=8-1
3) IR SENSOR MODULE - https://www.amazon.in/Products-Channel-Analogue-Digital-Follower/dp/B07GXL5L7J/ref=sr_1_2?keywords=ir+sensor&qid=1553455761&s=electronics&sr=1-2
4) DC MOTORS - https://www.amazon.in/Invento-Kg-cm-Shaft-Torque-Geared/dp/B07CKMFYDG/ref=sr_1_34?crid=32XN84K8LZ4PJ&keywords=dc+motor+500+rpm&qid=1553455839&s=gateway&sprefix=dc+motor+500%2Caps%2C320&sr=8-34
The sensor array draws 150mA at peak. Any suggestions as to where the problem might lie would be of great help. Thank you .
arduino-mega power motor ir
arduino-mega power motor ir
asked 2 hours ago
user9999114user9999114
61
New contributor
user9999114 is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.
asked 2 hours ago
user9999114user9999114
61
New contributor
user9999114 is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.
asked 2 hours ago
user9999114user9999114
61
New contributor
user9999114 is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.
asked 2 hours ago
user9999114user9999114
61
asked 2 hours ago
user9999114user9999114
61
61
New contributor
user9999114 is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.
New contributor
user9999114 is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.
user9999114 is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.
The buck converter is producing 5.5 V? That may be too low for the VIN input on Arduino, where the voltage regulator needs at least 7 V and is therefore causing brown-out.
– MichaelT
19 secs ago
add a comment |
The buck converter is producing 5.5 V? That may be too low for the VIN input on Arduino, where the voltage regulator needs at least 7 V and is therefore causing brown-out.
– MichaelT
19 secs ago
The buck converter is producing 5.5 V? That may be too low for the VIN input on Arduino, where the voltage regulator needs at least 7 V and is therefore causing brown-out.
– MichaelT
19 secs ago
The buck converter is producing 5.5 V? That may be too low for the VIN input on Arduino, where the voltage regulator needs at least 7 V and is therefore causing brown-out.
– MichaelT
19 secs ago
add a comment |
3 Answers
3
active
oldest
votes
The VIN pin goes to a 5V voltage regulator on the Arduino and needs at least about 7V minimum to work properly. If you want to supply 5V to an Arduino do it either on the 5V pin or via the USB connector. The VIN pin should receive 7V to 12V.
answered 2 hours ago
Jeff WahausJeff Wahaus
4185
This is the correct answer. VIN a high enough voltage to be regulated down to 5V. I suggest feeding 5V into your USB connector. That way you don't bypass the source switching and protection circuitry on the Arduino.
– Duncan C
28 mins ago
add a comment |
Resetting is due either to a software bug or voltage sag, and since it correlates with driving the motors harder, it's almost certainly the latter. You probably suspected as much since you mentioned the current draw of the sensor array. A quick experiment - disconnecting the sensors (and possibly a software patch to keep the robot running straight, without them) might help you discover the reason.
Each chip and each of its pin drivers has a current budget. It would be a good idea to look at the max current spec of the Atmega2560 and its pin drivers, and any other current specs mentioned in the datasheet, and make sure you're not trying to run it out of spec. The buck converter will have a limit, too, so make sure you're within its spec. If the output regulation of the buck converter is good enough, you can regulate it to 5v and bypass the Mega's on board regulator, for another saving.
answered 2 hours ago
JRobertJRobert
10.2k21136
add a comment |
One major drawback to working with motors is the large amounts of electrical noise they produce. This noise can interfere with your sensors and can even impair your microcontroller by causing voltage dips on your regulated power line. Large enough voltage dips can corrupt the data in microcontroller registers or cause the microcontroller to reset. You can avoid this problem by soldering capacitors along your motor terminals. Use 1µF ceramic capacitors for example
answered 45 mins ago
Zunzulla alagatyZunzulla alagaty
9111
add a comment |
Your Answer
StackExchange.ifUsing("editor", function ()
return StackExchange.using("schematics", function ()
StackExchange.schematics.init();
);
, "cicuitlab");
StackExchange.ready(function()
var channelOptions =
tags: "".split(" "),
id: "540"
;
initTagRenderer("".split(" "), "".split(" "), channelOptions);
StackExchange.using("externalEditor", function()
// Have to fire editor after snippets, if snippets enabled
if (StackExchange.settings.snippets.snippetsEnabled)
StackExchange.using("snippets", function()
createEditor();
);
else
createEditor();
);
function createEditor()
StackExchange.prepareEditor(
heartbeatType: 'answer',
autoActivateHeartbeat: false,
convertImagesToLinks: false,
noModals: true,
showLowRepImageUploadWarning: true,
reputationToPostImages: null,
bindNavPrevention: true,
postfix: "",
imageUploader:
brandingHtml: "Powered by u003ca class="icon-imgur-white" href="https://imgur.com/"u003eu003c/au003e",
contentPolicyHtml: "User contributions licensed under u003ca href="https://creativecommons.org/licenses/by-sa/3.0/"u003ecc by-sa 3.0 with attribution requiredu003c/au003e u003ca href="https://stackoverflow.com/legal/content-policy"u003e(content policy)u003c/au003e",
allowUrls: true
,
onDemand: true,
discardSelector: ".discard-answer"
,immediatelyShowMarkdownHelp:true
);
);
user9999114 is a new contributor. Be nice, and check out our Code of Conduct.
Sign up or log in
StackExchange.ready(function ()
StackExchange.helpers.onClickDraftSave('#login-link');
);
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
StackExchange.ready(
function ()
StackExchange.openid.initPostLogin('.new-post-login', 'https%3a%2f%2farduino.stackexchange.com%2fquestions%2f62846%2fwhy-is-arduino-resetting-while-driving-motors%23new-answer', 'question_page');
);
Post as a guest
Required, but never shown
3 Answers
3
active
oldest
votes
3 Answers
3
active
oldest
votes
active
oldest
votes
active
oldest
votes
The VIN pin goes to a 5V voltage regulator on the Arduino and needs at least about 7V minimum to work properly. If you want to supply 5V to an Arduino do it either on the 5V pin or via the USB connector. The VIN pin should receive 7V to 12V.
answered 2 hours ago
Jeff WahausJeff Wahaus
4185
This is the correct answer. VIN a high enough voltage to be regulated down to 5V. I suggest feeding 5V into your USB connector. That way you don't bypass the source switching and protection circuitry on the Arduino.
– Duncan C
28 mins ago
add a comment |
The VIN pin goes to a 5V voltage regulator on the Arduino and needs at least about 7V minimum to work properly. If you want to supply 5V to an Arduino do it either on the 5V pin or via the USB connector. The VIN pin should receive 7V to 12V.
answered 2 hours ago
Jeff WahausJeff Wahaus
4185
This is the correct answer. VIN a high enough voltage to be regulated down to 5V. I suggest feeding 5V into your USB connector. That way you don't bypass the source switching and protection circuitry on the Arduino.
– Duncan C
28 mins ago
add a comment |
The VIN pin goes to a 5V voltage regulator on the Arduino and needs at least about 7V minimum to work properly. If you want to supply 5V to an Arduino do it either on the 5V pin or via the USB connector. The VIN pin should receive 7V to 12V.
answered 2 hours ago
Jeff WahausJeff Wahaus
4185
The VIN pin goes to a 5V voltage regulator on the Arduino and needs at least about 7V minimum to work properly. If you want to supply 5V to an Arduino do it either on the 5V pin or via the USB connector. The VIN pin should receive 7V to 12V.
answered 2 hours ago
Jeff WahausJeff Wahaus
4185
answered 2 hours ago
Jeff WahausJeff Wahaus
4185
answered 2 hours ago
Jeff WahausJeff Wahaus
4185
answered 2 hours ago
Jeff WahausJeff Wahaus
4185
4185
This is the correct answer. VIN a high enough voltage to be regulated down to 5V. I suggest feeding 5V into your USB connector. That way you don't bypass the source switching and protection circuitry on the Arduino.
– Duncan C
28 mins ago
add a comment |
This is the correct answer. VIN a high enough voltage to be regulated down to 5V. I suggest feeding 5V into your USB connector. That way you don't bypass the source switching and protection circuitry on the Arduino.
– Duncan C
28 mins ago
This is the correct answer. VIN a high enough voltage to be regulated down to 5V. I suggest feeding 5V into your USB connector. That way you don't bypass the source switching and protection circuitry on the Arduino.
– Duncan C
28 mins ago
This is the correct answer. VIN a high enough voltage to be regulated down to 5V. I suggest feeding 5V into your USB connector. That way you don't bypass the source switching and protection circuitry on the Arduino.
– Duncan C
28 mins ago
add a comment |
Resetting is due either to a software bug or voltage sag, and since it correlates with driving the motors harder, it's almost certainly the latter. You probably suspected as much since you mentioned the current draw of the sensor array. A quick experiment - disconnecting the sensors (and possibly a software patch to keep the robot running straight, without them) might help you discover the reason.
Each chip and each of its pin drivers has a current budget. It would be a good idea to look at the max current spec of the Atmega2560 and its pin drivers, and any other current specs mentioned in the datasheet, and make sure you're not trying to run it out of spec. The buck converter will have a limit, too, so make sure you're within its spec. If the output regulation of the buck converter is good enough, you can regulate it to 5v and bypass the Mega's on board regulator, for another saving.
answered 2 hours ago
JRobertJRobert
10.2k21136
add a comment |
Resetting is due either to a software bug or voltage sag, and since it correlates with driving the motors harder, it's almost certainly the latter. You probably suspected as much since you mentioned the current draw of the sensor array. A quick experiment - disconnecting the sensors (and possibly a software patch to keep the robot running straight, without them) might help you discover the reason.
Each chip and each of its pin drivers has a current budget. It would be a good idea to look at the max current spec of the Atmega2560 and its pin drivers, and any other current specs mentioned in the datasheet, and make sure you're not trying to run it out of spec. The buck converter will have a limit, too, so make sure you're within its spec. If the output regulation of the buck converter is good enough, you can regulate it to 5v and bypass the Mega's on board regulator, for another saving.
answered 2 hours ago
JRobertJRobert
10.2k21136
add a comment |
Resetting is due either to a software bug or voltage sag, and since it correlates with driving the motors harder, it's almost certainly the latter. You probably suspected as much since you mentioned the current draw of the sensor array. A quick experiment - disconnecting the sensors (and possibly a software patch to keep the robot running straight, without them) might help you discover the reason.
Each chip and each of its pin drivers has a current budget. It would be a good idea to look at the max current spec of the Atmega2560 and its pin drivers, and any other current specs mentioned in the datasheet, and make sure you're not trying to run it out of spec. The buck converter will have a limit, too, so make sure you're within its spec. If the output regulation of the buck converter is good enough, you can regulate it to 5v and bypass the Mega's on board regulator, for another saving.
answered 2 hours ago
JRobertJRobert
10.2k21136
Resetting is due either to a software bug or voltage sag, and since it correlates with driving the motors harder, it's almost certainly the latter. You probably suspected as much since you mentioned the current draw of the sensor array. A quick experiment - disconnecting the sensors (and possibly a software patch to keep the robot running straight, without them) might help you discover the reason.
Each chip and each of its pin drivers has a current budget. It would be a good idea to look at the max current spec of the Atmega2560 and its pin drivers, and any other current specs mentioned in the datasheet, and make sure you're not trying to run it out of spec. The buck converter will have a limit, too, so make sure you're within its spec. If the output regulation of the buck converter is good enough, you can regulate it to 5v and bypass the Mega's on board regulator, for another saving.
answered 2 hours ago
JRobertJRobert
10.2k21136
answered 2 hours ago
JRobertJRobert
10.2k21136
answered 2 hours ago
JRobertJRobert
10.2k21136
answered 2 hours ago
JRobertJRobert
10.2k21136
10.2k21136
add a comment |
add a comment |
One major drawback to working with motors is the large amounts of electrical noise they produce. This noise can interfere with your sensors and can even impair your microcontroller by causing voltage dips on your regulated power line. Large enough voltage dips can corrupt the data in microcontroller registers or cause the microcontroller to reset. You can avoid this problem by soldering capacitors along your motor terminals. Use 1µF ceramic capacitors for example
answered 45 mins ago
Zunzulla alagatyZunzulla alagaty
9111
add a comment |
One major drawback to working with motors is the large amounts of electrical noise they produce. This noise can interfere with your sensors and can even impair your microcontroller by causing voltage dips on your regulated power line. Large enough voltage dips can corrupt the data in microcontroller registers or cause the microcontroller to reset. You can avoid this problem by soldering capacitors along your motor terminals. Use 1µF ceramic capacitors for example
answered 45 mins ago
Zunzulla alagatyZunzulla alagaty
9111
add a comment |
One major drawback to working with motors is the large amounts of electrical noise they produce. This noise can interfere with your sensors and can even impair your microcontroller by causing voltage dips on your regulated power line. Large enough voltage dips can corrupt the data in microcontroller registers or cause the microcontroller to reset. You can avoid this problem by soldering capacitors along your motor terminals. Use 1µF ceramic capacitors for example
answered 45 mins ago
Zunzulla alagatyZunzulla alagaty
9111
One major drawback to working with motors is the large amounts of electrical noise they produce. This noise can interfere with your sensors and can even impair your microcontroller by causing voltage dips on your regulated power line. Large enough voltage dips can corrupt the data in microcontroller registers or cause the microcontroller to reset. You can avoid this problem by soldering capacitors along your motor terminals. Use 1µF ceramic capacitors for example
answered 45 mins ago
Zunzulla alagatyZunzulla alagaty
9111
answered 45 mins ago
Zunzulla alagatyZunzulla alagaty
9111
answered 45 mins ago
Zunzulla alagatyZunzulla alagaty
9111
answered 45 mins ago
Zunzulla alagatyZunzulla alagaty
9111
9111
add a comment |
add a comment |
user9999114 is a new contributor. Be nice, and check out our Code of Conduct.
user9999114 is a new contributor. Be nice, and check out our Code of Conduct.
user9999114 is a new contributor. Be nice, and check out our Code of Conduct.
user9999114 is a new contributor. Be nice, and check out our Code of Conduct.
Thanks for contributing an answer to Arduino Stack Exchange!
- Please be sure to answer the question. Provide details and share your research!
But avoid …
- Asking for help, clarification, or responding to other answers.
- Making statements based on opinion; back them up with references or personal experience.
To learn more, see our tips on writing great answers.
Sign up or log in
StackExchange.ready(function ()
StackExchange.helpers.onClickDraftSave('#login-link');
);
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
StackExchange.ready(
function ()
StackExchange.openid.initPostLogin('.new-post-login', 'https%3a%2f%2farduino.stackexchange.com%2fquestions%2f62846%2fwhy-is-arduino-resetting-while-driving-motors%23new-answer', 'question_page');
);
Post as a guest
Required, but never shown
Sign up or log in
StackExchange.ready(function ()
StackExchange.helpers.onClickDraftSave('#login-link');
);
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
Sign up or log in
StackExchange.ready(function ()
StackExchange.helpers.onClickDraftSave('#login-link');
);
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
Sign up or log in
StackExchange.ready(function ()
StackExchange.helpers.onClickDraftSave('#login-link');
);
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
The buck converter is producing 5.5 V? That may be too low for the VIN input on Arduino, where the voltage regulator needs at least 7 V and is therefore causing brown-out.
– MichaelT
19 secs ago